Forum of Site of ValeraVi   


Forum Rules Информация (Information)

К ВАШЕМУ СВЕДЕНИЮ: На таких известных формах как forum.siemens-club.org, forum.allsiemens.com вы можете найти больше информации по проблемам установки патчей и их решению

Reply to this topicStart new topicStart Poll

> How to Apply Incflex Patch on S55 - English, Help for a beginner to apply the inflex patch to an S55 phone
PatroklosB
#4633 Posted: 19-06-2006, 19:06
Quote Post


Newbie
*

Profile
Group: Members
Siemens S55
Posts: 2
Member No.: 2304
Joined: 16-05-2006
Location: Chicago(US) & Budapest(EU)



Hello folks,

I speak little Russian, this is in English. I apologise.

I am a beginner in this area (have never "patched" before) and would like to apply the flex memory increase patch to an S55 mobile phone with firmware 91 and language pack 3 (lg3). I downloaded VKlay (latest version), the patch and the instructions. There are quite a things that I don't understand in the instructions; below are my questions. I have pasted the instructions at the end of this letter for quick reference.

1. General question - Overview of the procedure

My initial "belief" was that the patching would go roughly along the following lines:

a. I download the complete memory content of the phone ("fubu")
b. I edit this memory content with a suitable editor ("patching")
c. I then write back this edited content to the memory of the phone.

BUT
If I understand the instructions correctly, this NOT so. Rather, there are several occasions when I am supposed to "Write Memory" to the phone. So:

a. I download the complete memory content of the phone ("fubu")
b. I edit this content (and the language part, separately) "one by one" in certain ways (section 3, 4, 5 in the instructions)
c. After each edit, I write the edited content onto the phone, separately.
d. Finally, after the "culmination" of several writes, the phone is "patched".

Is this correct? So the phone has to be connected to the computer throughout the procedure and finally, after several writes, the patch is applied?


The questions below are about some details not clear to me.

2. About language packs - Section 4 in the instructions

Section 4 in the Instructions is about "Cutting and Transfering" the language pack
The phone I have has language pack 3 on it (lg3). This has 6 languages in it. I would like to keep 2 of these languages (English, Hungarian). Now:

- how to I get the "language pack" I am supposed to "cut"? Somehow from the phone? from the fubu? or from some external source?
- suppose I got the language pack. How do I "cut" it?
- will the phone have T9 on these two languages after the patch? (it has T9 for both languages now)

3. Section 6 in the instructions: "Apply patch below"

How do I actually do that?
(remember, I'm completely new to this patching business)


Thank you for all you help

PB

Below are the instructions copied here for convenience.
============================================



/*
1. Backup
1.1. Use V_Klay 2.6 - http://www.vi-soft.com.ua/index_e.htm
1.2. Download your fubu.
1.3. Download all files by help DES.
2. Undo old patches
2.1. Undo previous versions of this parch.
2.2. Undo patch "Moving T9".
3. Moving T9
3.1. Run V_Klay, choose "Flasher".
3.2. Open your fubu, which was saved BEFORE increasing flex-memory.
3.3. Set: FromAddress=3C0000, Size=040000, UseFromOffset=480000.
3.4. Press "Write Memory", press "Yes".
4. Cutting and transfer langpack.
4.1. Cut langpack to 1 or 2 or 3 languages (it's size should
be not more than 192K). Or use this archive
http://avkiev.siemens-club.ru/Siemens/Patc...55lg91-EnRu.rar
or:
http://www.vi-soft.com.ua/siemens/patches/...55lg91-EnRu.rar
4.2. Open binary langpack-file in V_Klay-Flasher.
4.3. Set: Address=0D0000, size don't change, UseFromOffset=0.
4.4. Press "Write Memory", press "Yes".
5. Transfer EELITE
5.1. Open your fubu (point 1.2) by help WinHex.
5.2. Save area BE0000-BEFFFF as new file. Its size must be 65536 bytes.
5.3. Open this file by help WinHex.
5.4. Press Ctrl-Alt-H (Replace Hex Values).
5.5. Check on "Replace all", "Use as wildcard", "3F", "All".
5.6. Set SearchFor=F03F3F3F3F3FFE3F3F3F3FF0,
ReplaceWith=F03F3F3F3F3FF63F3F3F3FF0. Press Ok. Press Ok.
5.7. Press Ctrl-Alt-H (Replace Hex Values).
5.8. Set SearchFor=FC3F3F3F3F3FFE3F3F3F3FFC,
ReplaceWith=FC3F3F3F3F3FF63F3F3F3FFC. Press Ok. Press Ok.
5.9. Save this file with new name.
5.10.Open this file in V_Klay-Flasher.
5.11. Set: Address=B60000, size don't change, UseFromOffset=0.
5.12. Press "Write Memory", press "Yes".
6. Apply patch below.
7. Turn on the phone, wait while memory will formatted.
8. Upload to the phone all files, which were downloaded in point 1.3.
9. Enjoy disk 1.71М.
PS. It is final release, I don't see any chances
increase flex-memory more.
PPS. If something wrong - just restore your phone
from backup (point 1.2).
PPPS. New addresses: langpack: 0D0000-0FFFFF, T9: 3C0000-3FFFFF,
EEPROM: B60000-B6FFFF and BF0000-BFFFFF.
*/

PMEmail Poster
Top
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
« Next Oldest | Обсуждение патчей (Patches discussions) | Next Newest »

Reply to this topic Fast Reply Start new topicStart Poll

> Fast Reply

For insert quote, select desired text and press here



Show Smilies Pop Up Window |  Enable Smilies |  Enable Signature